grundo

The Motorola Net6200/166 ??? (TODO: Paste the research Purple helped with)

Specs

Processor

2x PowerPC 604e @ 166 MHz

Memory

8 72-pin SIMM module slots

Hard disk

Seagate BarraCuda 4 Series 4.29 GB 7200RPM Fast Wide SCSI 1MB Cache

Display adapter

Cirrus Logic GD5446 Rev A

VRAM

2 MiB

Ethernet adapter

ZNYX NetBlaster ZX345 (SA0025)

SCSI card

Adaptec AHA-2940UW

Expansion

4 Conventional PCI slots, 3 16-bit ISA slots

Clock battery

Duracell 3V DL1/3N (one-third N)

Serial number

MP00176

Motherboard label

MLU, LX SERIES 01-07582-03 (FIREPOWER SYSTEMS INC), serial LXM01113

Firmware version

Version 03.03

Firmware timestamp

1996-09-19,01:47:29

Capacitors

21 of 25NXA220MEFC10X12.5 CAP ALUM 220UF 20% 25V RADIAL

Quirks

• The motherboard is labeled Firepower Systems, Inc. instead of Motorola.
• When the system was first powered on, it booted enough to give a "no RAM" beep. Later attempts did not give a beep. There are four diagnostic LEDs on the board labeled A, B, C, D. When booting with RAM, light A stays on. When booting with no RAM, light C stays on. When booting with no processor card, no lights stay on. The beep no longer happens. Purple believes this may be due to the capacitors no longer being able to function properly and only managed to work for the initial power-on before becoming useless for further attempts.
• After recapping, we discovered that when COMM 1 is attached to serial at 19200 baud, the system prints "AbcdefgBCD", first the first seven characters, then a pause, then the last three. Sometimes, it gets to "AbcdefgBCDE" after a second pause. Sometimes, there is a garbage character instead of this 'E'. Our hypothesis after this was that the machine doesn't like non-ECC RAM.
• After installing two sticks of EDO ECC 60ns RAM, the machine finally boots.
• The machine cannot be run without a keyboard. It will read garbage off the keyboard port and endlessly try to interpret invalid Forth commands, as seen from the serial console.
• Serial output only goes past "install-console" if no display is connected.

Documentation

• Q132858: PowerStack with Cirrus Video Adapter Hangs During Startup ^(variants)
• Q140475: PRB: Unable to Print to LPT1: Under Windows NT on Motorola ^(variants)
• Q153399: Add-in Display Adapters and Motorola Powerstack Computers ^(variants)
• Q154720: Using FDOS on the PowerPC ^(variants)
• Q154831: Arcinst Not Available for PPC ^(variants)
• Q154855: System Reserved Partitions on PowerPCs ^(variants)
• Q155407: Setting Up Windows NT on Motorola PowerStack When Drive Is New ^(variants)

Potential documentation

• https://web.archive.org/web/19970605064417/http://www.mot.com/GSS/MCG/support/hard/index.html

What a successful boot looks like over the serial port

AbcdefgBCDElxhHjklmBCDEoFGIJKLMN$1234#noFGIJKLMN$1234#stand-init

/pci/isa/interrupt-controller init

init-slaves

master-cache-on

/pci/isa/rtc

/pci/isa/nvram

init-nvram-buffer

init-options

init-security

/ clock frequency

more-memory

?bailout

scrub-memory

hardware-kludge

copy-reboot-info

nvramrc

probe-all

probe-isa

probe-pci

get-mac-address

probe-onboard

probe-ide

init-scsi

init-ide

install-console

History

• 2023-09-09: The computer is purchased at VCF Midwest.
• 2023-09-10: The computer is temporarily transported to my parents' place.
• 2023-09-28: The computer is transported to the new home.
• 2023-12-16: 📈 The clock battery is replaced. Before replacing, it was measuring 2.9 V.
• 2023-12-16: The capacitors on multiple components are identified as bad.
• 2024-01-14: 📈 21 capacitors are replaced (8 on processor card, 13 on motherboard.
• 2024-01-24: 📈 The correct RAM is installed.